or call
(913) 927 6144
OVERLAP SWING COOLER / FREEZER DOOR
FEATURES:
-
Leightweight, easy entry
-
Stainless Steel door trim
-
Made to custom-designed applications
-
USDA approved
Therm L Tec's overlap swing cooler / freezer doors are appropriate in a wide variety of applications. This door is most often used as a pedestrian traffic door for processors, dairies, freezers laboratories, coolers or any controlled environment.
Therm L Tec doors come in a broad variety of finishes. In all cases the door comes trimmed with Stainless Steel, a chrome latch and cam lift hinges.
Options:
-
10 W / foot heat in doors gasket and bottom, additional heat in door frame available (total 20 W / foot heat)
-
Double swing equipment room door
-
Insulated vision panel
-
Flush Sill or High Sill
-
Door Closer
-
Meat Rail Provision
-
Panic hardware and pilfer proof screws
-
Exit only door
-
Stainless Steel Kick Plates
-
Stainless Steel Hardware
-
High R Value
-
Full Caustic Washdown
Standard Sizes (Custom options available):
-
Height - 2' 6" - 8'
-
Width - 2' 6" - 7'
-
Thickness - 4", 6"
Door Details
Specifications:
IN-FITTING COOLER / FREEZER DOORS
DIVISION 8 | SECTION 8325
PART 1 [ GENERAL ]
1.01 | SCOPE
Work required under this section shall include the furnishing of all labor, materials, tools and equipment to complete insulated door work as detailed on drawings or as specified herein.
1.02 | SYSTEM DESCRIPTION
All doors, door casings shall be fully clad on all exposed surfaces with paint, white embossed or flat 26ga G90 galvanized steel. All hardware shall be protected against corrosion. Doors with provision for locking shall have safety release on opposite site.
1.03 | SUBMITTAL
In Compliance with specification requirements, submit shop drawings including all information required for complete installation, head jamb and sill conditions and electrical requirements.
1.04 | QUALITY ASSURANCE
Doors shall be installed in accordance with the architects plans and specifications and door manufacturer's written instructions, drawings and recommendations.
1.05 | DELIVERY, STORAGE & HANDLING
Each Door shall be adequately crated to protect door from damage during shipment and handling. Each crate shall be marked with door identification number. Inspect door for damage at time of receipt. Storage of door at jobsite to be protected from weather.
1.06 | WARRANTY
Doors shall be warranted against defective materials and workmanship for a period of one year.
PART 2 [ PRODUCTS ]
2.01
This specification is written with Therm-L-Tec, Series 300 insulated doors as basic performance standards. No substitution will be considered unless approved in writing by the architect.
2.02 | MANUFACTURED UNITS
-
Provide in-fitting cooler / freezer doors ( flush sill, high sill optional ). Door size and panel thickness as called for on drawings. Door panels to be free of wood; face casings and jamb to be wood, metal clad. Cam lift hinges and pad lockable latch with inside release, perimeter neoprene gasket and wiper seal at bottom. Where doors join in center there shall be no mullion, but they will fully gasketed. One leaf shall be considered in-active and shall have a Dutch latch at the top and a cane floor bolt.
-
Door is pre-hung in frame, hardware is factory installed. Entire unit ready for installation.
2.03 | ACCESSOIRS / OPTIONS
-
Provide U.L. approved perimeter heat cable on freezer doors.
-
High Sill
-
Back Trim (Mirror Image) casing
-
Emergency Exit Hardware
-
Optional Cladding Material
-
Vision Panel (heated on Freezer Door)
-
Kick Plates
-
Keyed Lockset
PART 3 [ EXECUTION ]
3.01 | INSTALLATION
-
Install doors in compliance with manufacturer's instructions and final shop drawings. Install frame plumb, level square and securely anchored in place with sufficient fasteners to support weight of door. Caulck at frame / wall juncture.
-
Install factory wired door assembly (heater cable junction box on freezer door) following manufacturer's instructions and local electrical codes. After field connections have been made to electrical service, test for proper operations.
3.02 | ADJUSTING AND CLEANING
-
Adjust doors to swing and latch easily with gasket sealing against face casings
-
Clean all doors of excess sealant, grease, stains, fingerprints and construction dust.